|
Issue |
Title |
|
Vol 5, No 3 (2015) |
Optimization of Machining Parameters in Electric Discharge Machining of Al 65032 |
Abstract
|
Jyoti bhaghi, Manjeet Bohat, V PS Kalsi, Sunil Dhingra |
|
Vol 5, No 3 (2015) |
Optimization of Process Parameters by Using CNC Milling Machining on EN-5 Steel |
Abstract
|
Raman Brar, Manjeet Bohat, V P S Kalsi, Sunil Dhingra |
|
Vol 5, No 3 (2015) |
Parametric Optimization of CNC Wire Cut EDM for Oil Harden Non-Shrinking Steel: A Comparative Study |
Abstract
|
Vedansh Chaturvedi, Anil Kumar Sharma |
|
Vol 5, No 2 (2015) |
Parametric Optimization of MRR in Manual Air Plasma Arc Cutting of AISI 1017 MS using Design of Experiment |
Abstract
|
Pratishtha Sharma, C. S. Malvi |
|
Vol 1, No 2 (2011) |
Parametric Optimization of Tool Wear Rate in Side Flushing form of Die Sink EDM of EN-31 Die Steel |
Abstract
|
Navdeep Malhotra, Sona Rani |
|
Vol 5, No 3 (2015) |
Parametric Study of Cylindrical Grinding Machine-Review |
Abstract
|
Amit L Dudhatra, Hardik N Chauhan, Tushar N Khilosia |
|
Vol 3, No 2 (2013) |
Plunger Technique: A New Approach to Stir Casting AMMC Preparation |
Abstract
|
B. P. Samal, A. K. Misra, S. C. Panigrahi, S. C. Mishra |
|
Vol 2, No 1 (2012) |
Pore Distributions in Porous Anodic Aluminum Oxide (PAAO) Surfaces of Pure and Commercial Aluminum Substrates |
Abstract
|
Manoj Kumar Kushwaha |
|
Vol 5, No 1 (2015) |
Prediction and Optimization of Laser Transformation Hardening Parameters of Unalloyed Titanium Using RSM |
Abstract
|
Duradundi Sawant Badkar, Krishnashankar Pandey, Buvanashekaran G |
|
Vol 2, No 2 (2012) |
Processing and Characterization of Ni2MnSn FSMA |
Abstract
|
Ajit Behera, S. C. Mishra |
|
Vol 3, No 1 (2013) |
Processing and Properties of In situ Synthesized Reinforcements in Molten Magnesium |
Abstract
|
Abhilash Viswanath, K.K Ajith Kumar, U.T.S. Pillai, B.C Pai |
|
Vol 6, No 3 (2016) |
Recovery of Iron Values from Iron Ore Slimes using Reagents |
Abstract
|
Rajesh Chintala, R.K. Rath, Anil Kumar |
|
Vol 6, No 3 (2016) |
Recovery of Iron Values from Waste Iron Ore Slime |
Abstract
|
Jyolsna Jerin, Rajendra Kumar Rath, Anil Kumar |
|
Vol 7, No 1 (2017) |
Recovery of Tungsten and Copper from Waste Tungsten Copper Borings |
Abstract
|
Nicky Kisku, D.C. Sau |
|
Vol 6, No 1 (2016) |
Reduction of Shrinkage-Porosity Defects in Sand Casting Using Finite Element Analysis: A Review |
Abstract
|
A V Vaishnav, M S Kagthara, H H Makwana |
|
Vol 3, No 1 (2013) |
Response of Sea Water Immersed GFRP Composite to Thermal Shock |
Abstract
|
A. P. Chakraverty, U. K. Mohanty, B. C. Ray |
|
Vol 3, No 1 (2013) |
Review of Nitrite Inhibitor for Protection of Rebar Corrosion |
Abstract
|
Altaf Ahmad, Anil Kumar |
|
Vol 6, No 1 (2016) |
Review on Application of Utility Poles for Power Transmission |
Abstract
|
Chinthada Manikanteswar Rao, Gudla Pavani, Kondapalli Siva Prasad |
|
Vol 5, No 3 (2015) |
Review on Corrosion of Welded Joints |
Abstract
|
Kondapalli Siva Prasad |
|
Vol 1, No 3 (2011) |
Sheqing LD Converter Lining to Sustainability – A Case Study |
Abstract
|
Dr. Priyavrat Thareja, Atul Kumar Singh |
|
Vol 6, No 1 (2016) |
Short Circuit MAG/MIG Welding and Fast ROOT Modified Short arc Welding Process for Sheet Metals Welding with Diverse Air Gap |
Abstract
|
Ashish Shukla, Nasir Khan, Manvendra Singh Sikarwar |
|
Vol 7, No 1 (2017) |
Simulation of Dual Microstructure Heat Treatment Process and Residual Stresses in Gas Turbine Disc by DeformHT Software |
Abstract
|
Adarsha H., Ramesh S., Kaushik V. Prasad, Ranganatha Swamy M. K. |
|
Vol 6, No 3 (2016) |
Solidification Curve Analysis of Cylindrical Casting by FEM |
Abstract
|
Dharmesh Barodiya, M.D. Mahajan, Shaheen Beg Mughal |
|
Vol 6, No 2 (2016) |
Statistical Analysis on Weld Bead Geometry of Pulsed Current Micro-plasma Arc Welded AISI 316Ti Austenitic Stainless Steel Sheets |
Abstract
|
Ch. Swetha, G. Siva Karuna |
|
Vol 1, No 3 (2011) |
Structural, Mechanical, Electrical and Magnetic Properties of Mn–Zn Substituted Ca-hexaferrites |
Abstract
|
Dr. C.L. Khobaragade |
|
76 - 100 of 117 Items |
<< < 1 2 3 4 5 > >> |